Mastercraft Maximum 4-in-1 Laser Pro Manual
. 5528 Answers SOURCE: I suspect there are several models but I have one model.
1) Turn on the unit (if the green light is blinking replace the battery). 2) Calibrate the unit by holding it flat against the wall for 5 seconds until the red light goes off and the beep stops. Make sure you do not move the unit during the calibration or position the unit over a stud (try a spot 6-12' away from the corner of the wall - most studs are on 16' or 24' centers and the wood/metal stud is 1 1/2' thick). If the unit keeps beeping or the red light doesn't go off during the calibration, move the unit sideways 5-8' in case you are above a water pipe or other reason for 'too deep a surface' for the unit. 3) Do not lift the unit off the wall or you will need to recalibrate it. Slide the unit across the wall.
When the upper red light comes on and the beeping starts, that marks one edge of the object in the wall (stud). Continue until the red light goes off and the beeping stops. Mark the other edge of the stud by moving the stud finder in the opposite direction and marking when the red light comes on and the beeping starts. The center of the two marks is the center of the stud for securing anything to the wall. If the beep persists over a 6' range, I'd check if you have any old cast-iron pipes or a door/window that was relocated in that wall. Repeating the test in a few places vertically along that spot of the wall will tell you there is a consistent large object in that location.
Neither a filled in window or door will run the entire length of the wall but you could be finding the headers (the vertical framing of the opening would probably be 4-6' wide (double or triple stud depening on the needs of the house design)). I hope this helps. Cindy Wells (on another stud-finder that I borrow, you press the buttons on the right and left side to turn it on. Calibrate by holding it to the wall for a short while and then slide it across the wall. Note when the top red led lights and the beep starts. Repeat in reverse to find the other side of the stud.) Posted on Sep 18, 2010.
View & download of more than 446 Mastercraft PDF user manuals, service manuals, operating guides. Boat, Power tool user manuals, operating guides & specifications. Operator's Manual. SLIDING COMPOUND. MITER SAW WITH LASER TRAC. WARNING ICONS. Your power tool and its Operator's Manual may contain “WARNING ICONS”. The maximum depth travel of the cutting head was. View & download of more than 446 Mastercraft PDF user manuals, service manuals, operating guides. Boat, Power tool user manuals, operating guides & specifications.
. Self-levelling CroSS-line laSer level 057-4587-6. Keep this instruction manual for future use. Should this product be passed on to a third WarranTY 20–21 party, then this instruction manual must be included. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6.
7.4 oz (210 g) Do not attempt to modify the performance of the laser device in any way. This may result in a dangerous exposure to laser radiation. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6. Do not operate the tool in combustible areas, such as in the presence of flammable liquids, gases, or dust. Use of other accessories that have been designed for use with other laser tools could result in serious injury. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6. Do not mix old and new batteries.
remove depleted batteries immediately, and dispose of them according to the laws and regulations governing your community. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6.
Laser Pro Software For Banking
To turn the laser off, press the mode button repeatedly until the laser shuts off. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6. mounting wall fixtures, electrical outlets, switches and lighting. installing a drop ceiling.
Painting. installing closets. laying tile and flooring Description Description Knob 1 1/4' screw platform Knob 2 Handle self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6.
Tighten Knob 2 again to lock the position. After adjustment tighten 1/4' Knob 1 (fig 5 and fig 6). Fig 6 fig 8 360° fig 9 self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6. If the problem remains unsolved after performing the checks described above, call the toll-free helpline, at 1-800-689-9928. after you have finished using the tool, always make sure that the switch is in the off position. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6.
Mastercraft Maximum 4 In 1 Laser Pro User Guide
Battery cover rubber Protector 000 right Housing If any parts are missing or damaged, or if you have any questions, please call the Toll-free Helpline, at 1-800-689-9928. Self-levelling cross-line laser level - 057-4587-6 self-levelling cross-line laser level - 057-4587-6. 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following components: accessories, which are guaranteed for a period of 1 year from the date of original retail purchase against defects in workmanship and materials. BY MaSTerCrafT CanaDa ToronTo, CanaDa M4S 2B8 self-levelling cross-line laser level - 057-4587-6.